This website uses cookies to provide services, personalise ads and analyse the visitor traffic. By using this site you agree to their use. Close
Shop roku 2022

Samco Sport silicone elbow 45° with inner diameter 11 mm, color gunmetal grey

Samco Sport silicone elbow 45° with inner diameter 11 mm and wall thickness 4,0 mm. This silicone elbow can be used for distribution of pressurized air, coolant, for intake and intercooler piping and many more purposes.

ATTENTION: This silicone elbow is not fuel or oil resistant. For distribution of fuel or oil please use Samco ProFuel or Samco Fluoro hoses.Full description

22,22
Cena je včetně DPH
color

blue
19,31 €

red
19,31 €

black
19,31 €

yellow
19,31 €

orange
19,31 €

bright green
19,31 €

dark green
22,22 €

purple
22,22 €

white
22,22 €

gunmetal grey
22,22 €

viper red
22,22 €

classic black
22,22 €

vintage black
22,22 €

urban camo
26,09 €

solar orange camo
26,09 €

ninja green camo
26,09 €

lightning blue camo
26,09 €

samco blaze
26,09 €

fire red camo
26,09 €
P/N: E45/11(GMS)
Add to list
Oblíbené položky můžete přidávat až po Login.
 

Samco Sport silicone hoses have a variety ways of use for distribution of pressurized air, coolant or for intercooler and intake piping. Samco Sport hoses are available in many colors which makes them a perfect adiction to the perfect look of your engine bay. It's possible to cut the universal hoses to legth you need and connect them together with specific couplers and clamps. These clamps must not have a sharp edge which can damage the hose.

Technical parameters:
Inner diameter: 11 mm
Bending angle: 45°
Wall thickness: 4,0 mm
Leg length: 63 mm
Temperature resistance: max. 180°C

ATTENTION: This silicone elbow is not fuel or oil resistant. For distribution of fuel or oil please use Samco ProFuel or Samco Fluoro hoses.

How to measure 45° elbows:


Silicone elbows and hoses are available in various colours to perfectly fit the design of your car. Please note that because of our wide variation of color options, most parts are made to order.

Basic price is in association with standard colors (blue, red, light green, yellow, black and orange)
Premium colors with 15% surcharge: violet, British Racing Green, white, matte black (Classic), matte black (Vintage), Gunmetal grey, Viper red
Samco Sport Camo patterns with 35% surcharge: fire red camo, lightning blue camo, ninja green camo, urban camo, solar orange camo, blaze

 

Použití silikonových hadic Samco Sport posouvá limity vozu Extrémní odolnost a životnost silikonových hadic Samco Sport Kvalita silikonových hadic Samco Sport je ověřena použitím v extrémních podmínkách
Samco Sport silicone hoses are pushing the performance limits of your car and also are giving an attractive look to the engine bay. Samco Sport silicone hoses are the most durable silicone hoses on the market. This fact is supported by the lifetime warranty. The proffessional racing teams around the world have chosen Samco Sport as their silicone hoses supplier because Samco Sport hoses proved their endurance during the most extreme races in the most extreme conditions.

 

To qualify for the extended warranty the original purchaser must complete this “warranty registration form”. The form must be completed within 30 days after the purchase date.

SAFETY INSTRUCTIONS

Before CONNECTING, ensure the following important safety precautions are observed:

  • Switch off engine and disconnect battery.
  • Ensure vehicle/bike is suitably parked, and secured to prevent any unexpected vehicle movement.
  • Allow engine, coolant system and all pipework to fully cool (coolant can retain heat for several hours after engine has been switched off).

CONNECTING OF YOUR HOSES

  1. Care must be taken to drain and dispose of the old coolant fluids. Please ensure local environmental laws are observed when disposing of any fluids and old hoses.
  2. When installing direct-replacement kits, remove OEM/stock hoses one at a time and replace them with the equivalent shaped Samco hose as you go – check the orientation of each hose.
  3. The hose must be aligned properly or it will not sit square on the pipework. Any attempt to force it on square may lead to abrasion on the hose from the end of the pipework. The clamp must be positioned at least 3/8” (10mm) down from the open end of the pipe-work, and behind any bead or lip on the pipe-work. Ensure the clamp is fully seated on the hose with at least 3/8”(10mm) of hose protruding past the clamp. Take care not to damage the lining of the hose when installing.

  4. Samco Clamps should be tightened to the following torque setting:

    Always refer to manufacturers recommendations for any specific torque recommendations.

    3 Nm for hoses with inner diameter 12-20 mm
    5 Nm for hoses with inner diameter 22-45 mm
    6 Nm for hoses with inner diameter larger then 50 mm
    They should be tested again to this torque setting 30 minutes after installation to allow for any stress-relaxation in the silicone.
  5. For coolant hoses, when re-filling with coolant, ensure that the vehicle/bike manufacturer’s instructions for re-filling coolant are followed. Use an Ethylene-glycol based coolant. Please note, other coolants and additives may invalidate the warranty.
  6. Inspect for leaks, and periodically check the tightness of hose clamps.
  7. Periodically clean hoses using Samco Sport hose cleaning products. Do not use any harsh cleaners, polishes or any
    petroleum-derived product – ensure safety precautions are observed when cleaning hoses.

Samco Sport hoses are expertly handcrafted to the highest automotive standards using the best quality fabrics. They are 100% visually inspected, and our lifetime guarantee ensures they are the best hoses money can buy. Hand made and tested in our own UK factory. Tried, tested and trusted by professional race teams and driven by enthusiasts.

Our company Escape6 is an official distributor of Samco Sport silicone hoses.

 

Samco Sport Connect to the track

Parameters and specifications

Internal diameter
11 mm
Shape of hose
elbow 45°
Hose endurance
Standard
Lenght
63 mm
Leg length
63 mm
Temperature resistant
180°C
Wall thickness
4,0 mm



Recommended accessories



APEK - Asociace pro elektronickou komerci APEK - Asociace pro elektronickou komerci

Our company Escape6 is on the market since year 2000. Our open and positive approach to vehicle modifications, besides many years of experience, stems from the enthusiasm of our entire team. Each of us is a true car enthusiast, and so we can identify with your idea of car modifications, whether it's a Show&Shine competitor, circuit racer, or offroad driver. We actively visit automobile exhibitions around the world, as well as domestic tuning exhibitions, events and events where you can meet our own modified cars.

We are looking forward to seeing you in our showroom in Prague Čestlice, which is filled with the best of today's world tuning parts and accessories. Whether you are only looking for small accessories or car care products, or if you want your car to be completely "tuned out", you are in the right place with us! And do not forget to follow us on social networks where you can learn something behind the scenes of our company.